BYPASS FRP & FLASH HM M3

FRP HM M3 Verifikasi akun Google ini mencegah pengguna yang tidak sah dari Mengakses atau menggunakan perangkat Anda jika telah ulang ke pengaturan pabrik tanpa izin Anda (misalnya, jika perangkat hilang atau dicuri)

Mohon digunakan dengan bijaksana, jangan digunakan pada hp curian dan kegiatan ilegal lainnya, thx

Model Name  : sp7731c_1h10_oversea
Model Brand : HM
Model Device: sp7731c_1h10
AndrVersion : 6.0
BaseBand CPU: SP7731CEA
Project Ver : MRA58K release-keys
Model Ext   : M3

 Simple dan cepet selesai, file cuman kurang dari 1MB, Flash gak nyampe 10dtk dah selesai. IRIT QUOTA

Bahan :

A. BYPASS FRP ONLY ukuran PAC 1 MB

B. ROM PAC FULL HM M3

     TOOL :

    1.  Download SPD_Upgrade_Tool_R4.0.0001 Download Disini
    2.  Driver SPD by InfinityBox
    3.  Tutorial Flash via research here
    4.  Konfirmasi pass sms only 0822-1163-1565 (nomor ini hanya buat konfirmasi, BUKAN YANG DI ISI) , Mahar pulsa 10k

    Cara Kerja :

    • Untuk FRP HM M3 tinggal pake PAC BYPASS FRP ONLY
    • Bila tidak jalan berheti di FDL1 branti versi tidak sama, silahkan gunakan versi lain
    • Bila terjadi Blank / MATOT berarti salah versi, silahkan ganti file FRP, atau Full Flash pake firmware PAC FULL
    • Boot volume (+)

    Cara Bypass FRP HM M3 via Research Download

    Cara Flash HM M3 via Research Download

    Log Read Firmware HM M3
    Operation : Read FullFlash [ v1.27 ]

    1. Remove battery. Insert battery back
    2. Press and hold ‘VolumeUp’ and ‘VolumeDown’ keys
     -> Alternative : just ONE ‘VolumeUp’ or ‘VolumeDown’ key
    3. Insert cable
     ====  Wait for phone…
    Phone found! [ 6 ]
    Port Opened
    Sync…
    InitBoot Done [ 0x81 ] , Ver : SPRD3
    Sync…
    Sending FDL
    [Info] : If SW freeze here more, than 15 seconds – remove cable
    PickUp loaders from pac
    FDL Ready!
    Boot Ver : Spreadtrum Boot Block version 1.1
    Sending FLASH FDL
    FLASH FDL Ready!
    Boot Ok!
    FlashMode Set : Ok!
    Detected eMMC Flash , Structure detect Ok!
    [FW_READER] : Prepare Ok!
    – > Wait phone connected …
    Phone found! [ 6 ]
    Port Opened
    Sync…
    InitBoot Done [ 0x81 ] , Ver : SPRD3
    Sync…
    Sending FDL
    [Info] : If SW freeze here more, than 15 seconds – remove cable
    PickUp loaders from pac
    FDL Ready!
    Boot Ver : Spreadtrum Boot Block version 1.1
    Sending FLASH FDL
    FLASH FDL Ready!
    Boot Ok!

    – > Wait phone connected …

    Phone found! [ 6 ]
    Port Opened
    Sync…
    InitBoot Done [ 0x81 ] , Ver : SPRD3
    Sync…
    Sending FDL
    [Info] : If SW freeze here more, than 15 seconds – remove cable
    PickUp loaders from pac
    FDL Ready!
    Boot Ver : Spreadtrum Boot Block version 1.1
    Sending FLASH FDL
    FLASH FDL Ready!
    Boot Ok!

    Model Name  : sp7731c_1h10_oversea
    Model Brand : HM
    Model Device: sp7731c_1h10
    AndrVersion : 6.0
    BaseBand CPU: SP7731CEA
    Project Ver : MRA58K release-keys
    Model Ext   : M3
    [Read Mode] : HSUSB : 0x3000
    [FW_READER] : Reading Firmware Now …
    [Read Ok] : u-boot-spl-16k.bin
    [Read Ok] : u-boot.bin
    [Read Ok] : prodnv.img
    [Read Ok] : sc7731C_CP0_modem.bin
    [Read Ok] : DSP_DM_Gx.bin
    [Read Ok] : nvitem_w.bin
    [Read Ok] : sc8830g_modem_CP2_WCN_Trunk_W16.28.5_Release.bin
    [Read Ok] : nvitem_wcn.bin
    [Read Ok] : logo_720x1280.bin
    [Read Ok] : logo2.bin
    [Read Ok] : logo3.bin
    [Read Ok] : logo4.bin
    [Read Ok] : logo5.bin
    [Read Ok] : logo6.bin
    [Read Ok] : logo7.bin
    [Read Ok] : logo8.bin
    [Read Ok] : logo9.bin
    [Read Ok] : logo10.bin
    [Read Ok] : boot.img
    [Read Ok] : system.img
    [Build Ok] : cache.img
    [Read Ok] : recovery.img
    [Read Ok] : sysinfo.img
    [Build Ok] : userdata.img

    AndroidInfo created
    Firmware Size : 1707 MiB
    Saved to : E:\hm\m3\New folder\SP7731CEA_sp7731c_1h10_6.0_MRA58K_release-keys_M3\
    Done!

    Flash Advan S4T SC7731 & SC7731C

    Model Name  : S4T
    Model Brand : ADVAN
    Model Device: S4T
    AndrVersion : 5.1.2
    BaseBand CPU: S4T
    Project Ver : S4T_WG4036_V0.5_20160406
    Model Ext   : S4T

    Bahan :

    1.  Download Firmware PAC ADVAN S4T V0.5 atau  Download Disini
    2.  Download Firmware PAC ADVAN S4T V1.2 atau  Download Disini
    3.  Download SPD_Upgrade_Tool_R4.0.0001 Download Disini
    4.  Driver SPD by InfinityBox
    5.  Tutorial Flash via research here
    6.  Konfirmasi pass sms only 0822-1163-1565 (nomor ini hanya buat konfirmasi, BUKAN YANG DI ISI) , Mahar pulsa 10k

    Error pada research download baca disini

    Note :
    1. Boot Volume UP
    2. Buat cek versi V05 atau V1.2 flash saja, bila tidak jalan berarti versi satunya

    Cara Flash Advan S4T via Research Download

    Log Read Firmware Advan S4T
    Operation : Read FullFlash [ v1.27 ]

    1. Remove battery. Insert battery back
    2. Press and hold ‘VolumeUp’ and ‘VolumeDown’ keys
     -> Alternative : just ONE ‘VolumeUp’ or ‘VolumeDown’ key
    3. Insert cable
     ====  Wait for phone…
    Phone found! [ 34 ]
    Port Opened
    Sync…
    InitBoot Done [ 0x81 ] , Ver : SPRD3
    Sync…
    Sending FDL
    [Info] : If SW freeze here more, than 15 seconds – remove cable
    FDL Ready!
    Boot Ver : SPRD 773x eMMC loader v3 Infinity
    Sending FLASH FDL
    FLASH FDL Ready!
    Boot Ok!
    FlashMode Set : Ok!
    Detected eMMC Flash , Structure detect Ok!
    [FW_READER] : Prepare Ok!
    – > Wait phone connected …
    Phone found! [ 34 ]
    Port Opened
    Sync…
    InitBoot Done [ 0x81 ] , Ver : SPRD3
    Sync…
    Sending FDL
    [Info] : If SW freeze here more, than 15 seconds – remove cable
    FDL Ready!
    Boot Ver : SPRD 773x eMMC loader v3 Infinity
    Sending FLASH FDL
    FLASH FDL Ready!
    Boot Ok!

    – > Wait phone connected …

    Phone found! [ 34 ]
    Port Opened
    Sync…
    InitBoot Done [ 0x81 ] , Ver : SPRD3
    Sync…
    Sending FDL
    [Info] : If SW freeze here more, than 15 seconds – remove cable
    FDL Ready!
    Boot Ver : SPRD 773x eMMC loader v3 Infinity
    Sending FLASH FDL
    FLASH FDL Ready!
    Boot Ok!

    Model Name  : S4T
    Model Brand : ADVAN
    Model Device: S4T
    AndrVersion : 5.1.2
    BaseBand CPU: S4T
    Project Ver : S4T_WG4036_V0.5_20160406
    Model Ext   : S4T

    [Read Mode] : HSUSB : 0x3000
    [FW_READER] : Reading Firmware Now …
    [Read Ok] : u-boot-spl-16k.bin
    [Read Ok] : u-boot.bin
    [Read Ok] : prodnv.img
    [Read Ok] : sc7731g_CP0_modem.bin
    [Read Ok] : DSP_DM_Gx.bin
    [Read Ok] : nvitem_w.bin
    [Read Ok] : sc8830g_modem_CP2_WCN_14D_W15.31.1_Release.bin
    [Read Ok] : nvitem_wcn.bin
    [Read Ok] : logo_480x800.bin
    [Read Ok] : fblogo_480x800.bin
    [Read Ok] : boot.img
    [Read Ok] : system.img
    [Build Ok] : cache.img
    [Read Ok] : recovery.img
    [Build Ok] : userdata.img
    AndroidInfo created
    Firmware Size : 1276 MiB
    Saved to : F:\ADVAN\ADVAN S4T\v05 ok\S4T_S4T_5.1.2_S4T_WG4036_V0.5_20160406_S4T\
    Done!

    Flash Mito A260 Kitkat & Lolypop

    Model Name  : MITO_A260
    Model Brand : MITO
    Model Device: MITO_A260
    AndrVersion : 4.4.2
    BaseBand CPU: H620
    Project Ver : MITO_A260_20150612_T04
    Model Ext   : MITO_A260

    Mito A260 KitKat T04 Disticker backcasing V3
    Mito A260 KitKat T07 Disticker backcasing V2

    Bahan :

    1.  Download Firmware PAC Mito A260 KitKat T04 atau  Download Disini
    2.  Download Firmware PAC Mito A260 KitKat T07 atau  Download Disini
    3.  Download Firmware PAC Mito A260 Lolypop T09 atau  Download Disini
    4.  Download SPD_Upgrade_Tool_R4.0.0001 Download Disini
    5.  Driver SPD by InfinityBox
    6.  Tutorial Flash via research here
    7.  Konfirmasi pass sms only 0822-1163-1565 (nomor ini hanya buat konfirmasi, BUKAN YANG DI ISI) , Mahar pulsa 10k

    Error pada research download baca disini

    Note :
    1. Boot Volume DOWN

    Cara Flash Mito A260 via Research Download

    Log Read Firmware Mito A260
    Operation : Read FullFlash [ v1.27 ]

    1. Remove battery. Insert battery back
    2. Press and hold ‘VolumeUp’ and ‘VolumeDown’ keys
     -> Alternative : just ONE ‘VolumeUp’ or ‘VolumeDown’ key
    3. Insert cable
     ====  Wait for phone…
    Phone found! [ 7 ]
    Port Opened
    Sync…
    InitBoot Done [ 0x81 ] , Ver : SPRD3
    Sync…
    Sending FDL
    [Info] : If SW freeze here more, than 15 seconds – remove cable
    FDL Ready!
    Boot Ver : SPRD 773x eMMC loader v3 Infinity
    Sending FLASH FDL
    FLASH FDL Ready!
    Boot Ok!

    FlashMode Set : Ok!
    Detected eMMC Flash , Structure detect Ok!

    [FW_READER] : Prepare Ok!
    – > Wait phone connected …

    Phone found! [ 7 ]
    Port Opened
    Sync…
    InitBoot Done [ 0x81 ] , Ver : SPRD3
    Sync…
    Sending FDL
    [Info] : If SW freeze here more, than 15 seconds – remove cable
    FDL Ready!
    Boot Ver : SPRD 773x eMMC loader v3 Infinity
    Sending FLASH FDL
    FLASH FDL Ready!
    Boot Ok!
    – > Wait phone connected …

    Phone found! [ 7 ]
    Port Opened
    Sync…
    InitBoot Done [ 0x81 ] , Ver : SPRD3
    Sync…
    Sending FDL
    [Info] : If SW freeze here more, than 15 seconds – remove cable
    FDL Ready!
    Boot Ver : SPRD 773x eMMC loader v3 Infinity
    Sending FLASH FDL
    FLASH FDL Ready!
    Boot Ok!
    Model Name  : MITO_A260
    Model Brand : MITO
    Model Device: MITO_A260
    AndrVersion : 4.4.2
    BaseBand CPU: H620
    Project Ver : MITO_A260_20150612_T04
    Model Ext   : MITO_A260
    [Read Mode] : HSUSB : 0x3000

    [FW_READER] : Reading Firmware Now …

    [Read Ok] : u-boot-spl-16k.bin
    [Read Ok] : u-boot.bin
    [Read Ok] : prodnv.img
    [Read Ok] : sc7731g_CP0_modem.bin
    [Read Ok] : DSP_DM_Gx.bin
    [Read Ok] : nvitem_w.bin
    [Read Ok] : sc7731g_modem_CP2_WCN_14E_W14.50_Release.bin
    [Read Ok] : nvitem_wcn.bin
    [Read Ok] : logo_480x800.bin
    [Read Ok] : fblogo_480x800.bin
    [Read Ok] : boot.img
    [Read Ok] : system.img
    [Build Ok] : cache.img
    [Read Ok] : recovery.img
    [Build Ok] : userdata.img

    AndroidInfo created
    Firmware Size : 907 MiB
    Saved to : E:\andro 1\mito\MITO A260\H620_MITO_A260_4.4.2_MITO_A260_20150612_T04_MITO_A260\
    Done!