Flash & Bypass FRP Novo Bonvi Note Verifikasi akun Google

FRP Novo Bonvi Note  Verifikasi akun Google ini mencegah pengguna yang tidak sah dari Mengakses atau menggunakan perangkat Anda jika telah ulang ke pengaturan pabrik tanpa izin Anda (misalnya, jika perangkat hilang atau dicuri)

Mohon digunakan dengan bijaksana, jangan digunakan pada hp curian dan kegiatan ilegal lainnya. thx

Brand     : NOVO

ProdName  : t586_dg_a56_novo

ProdModel : Bonvi Note

Device    : t586_dg_a56_novo

AndroidVer: 6.0

MTKxCPU   : MT6737T

MTKxPRJ   : alps-mp-m0.mp1-V2.84_wtk6737t.36.m0_P80

Bahan :

1. Download Bypass FRP Only

2. Download Firmware Full

3. Download SP-Flash-Tool Wajib pake versi ini Download Disini

4. Driver bila belum punya instal dulu driver mtknya

5.  Untuk tutorial flash via Flash tool bisa dilihat DISINI

6. Konfirmasi pass sms only 0822-1163-1565 (nomor ini hanya buat konfirmasi, BUKAN YANG DI ISI) , Mahar pulsa 10k

Cara Flash Bypass Frp Novo Bonvi Note via Flash Tool


Log Read Firmware Novo Bonvi Note

Operation : Read Flash [ v1.58 ]

1. Power Off Phone , Remove battery , Insert back
2. Insert USB cable. In some cases require hold BootKey

Wait for phone…
Phone found! [ 6 ]
Sync…
Inital Boot Ok!
BB_CPU_PID : 6735
BB_CPU_NME : [MediaTek] MT6735_S00
BB_CPU_EXT : 0xCA00 , 0x8A00 , 0x0000
Processing BROM stage
Settings for BROM configured!
SecCfgVal : 0x00000000
BromVer   : 0x00FF
BLVersion : 0x0001
PreLoader : Active [ Boot with PL ]
BootLdrSS : NORMAL with PRELOADER
Processing DA stage
DA Select done, will use MTK_AllInOne_DA_v5.1624.16.07
Sending and initialize DA …
Running DA ver.4.2 on BBID : 0x93
NAND Flash : NOT INSTALLED
eMMC Flash : 4500017045434148970A014133EAA83F
Initialize Memory …
DRAM already initialized by Preloader
DAgent sent , init HW now
eMMC FlashIC initialized
[eMMC] : FLASH_VEN : 0x70 , OEM : 0100
[eMMC] : FLASH_INF : [KINGSTON] , AECAH
[eMMC] : FLASH_CID : 700100454841434541010A973FA8A333
[eMMC] : FLASH_BRT : 0x00400000 , 0x00400000 , 0x00400000
[eMMC] : FLASH_LEN : 0x0000000390000000
[eMMC] : FLASH_UCP : 14592 MiB [eMMC 16 GiB]
DEV RID    : 0xFCC4CFBDAF4FDBA4CF0076BEE178F1A1
INT RAM    : 0x00020000
EXT RAM    : 0x80000000 [2 GiB]
BOOT TYPE  : EMMC_FLASH_BOOT
SOC VERIFY : C1
Boot Ok!

Reading Flash Content now …

xGPT : Normalize settings Ok!

Brand     : NOVO
ProdName  : t586_dg_a56_novo
ProdModel : Bonvi Note
Device    : t586_dg_a56_novo
AndroidVer: 6.0
MTKxCPU   : MT6737T
MTKxPRJ   : alps-mp-m0.mp1-V2.84_wtk6737t.36.m0_P80

[Read Ok] : preloader_t586_dg_a56_novo_37t36.bin
[Read Ok] : lk.bin
[Read Ok] : boot.img
[Read Ok] : recovery.img
[Read Ok] : logo.bin
[Read Ok] : secro.img
[Read Ok] : tz1.img
[Read Ok] : tz2.img
[Read Ok] : system.img
[Read Ok] : cache.img
[Read Ok] : userdata.img

[ScatCFG] : MT6735 / V1.1.2 / t586_dg_a56_novo_37t36 / EMMC
Android Info saved
MAUI Meta DB saved
HWConfig Info saved
FW Size : 2960 MiB
Scatter saved to : D:\novo\MT6737T__NOVO__Bonvi_Note__t586_dg_a56_novo__6.0__alps-mp-m0.mp1-V2.84_wtk6737t.36.m0_P80\

syarat-dan-ketentuan

 

Flash Asus X009DA Dead via 9008 ~ CM2

Device Brand    : asus

Device Manufact.: asus

Device Model    : msm8916_32

Device CPU      : MSM8916

Device IntName  : WW_Phone

Device Version  : 6.0.1

CU_SWVer        : asus_x009da

Device Compile  : 3/29/2017 10:02:02 AM

Fix Asus X009DA matot via 9008, tool wajib pake CM2.

Bahan :

  • via EDL 9008 / CM2
  1.       Download Rom Asus X009DA HS-9008  atau Download Disini
  2.       Tool WAJIB menggunakan dongle CM2
  3.       Cara kerja ikuti petunjuk CM2, boot volume up+down, kabel edl
  4.       Konfirmasi pass sms only 0822-1163-1565 (nomor ini hanya buat konfirmasi, BUKAN     YANG DI ISI) , Mahar pulsa 10k

Cara Flash Asus X009DA via dongle CM2

Operation : Read Flash [ v1.16 ]

1. Power Off Phone , Remove battery , Insert back
2. PRESS and HOLD BOTH VOLUME KEYS!
3. Insert USB cable. In some cases require use EDL cable or TP to force EDL mode!

Wait for phone…
Device Found!
Initialize …
Handshake passed!
ID_BLOCK_I : SnapDragon 410 [MSM8916]
ID_BLOCK_S : 09F6ED7C
ID_BLOCK_L : 4B05FC6FC932A2372DC731FBDB7B5FDD
ID_BLOCK_L : 238EEACE428CCE9EE75A26A3FF8B1F7B
Use CM2 Internal Loader
Loader Sent! Initializing …
Running FireHose on BBID : MSM8916 , FLASH : eMMC , mVER : 1
MemInfo : 0x0003 / 0x0200 / 0x00000001D2000000 [ eMMC 8 GiB ]
ExtInfo : 0x00004000/00004000/00001000/00001000/00000200
Boot Ok!

Brand     : asus
ProdName  : WW_Phone
Device    : msm8916_32
AndroidVer: 6.0.1
Manufact. : asus
QLMxCPU   : MSM8916
Asus X009DA
DevInfo : MSM8916__asus__asus__ANDR_v6.0.1__msm8916_32__WW_Phone

Reading Flash Content …
[Read Ok] : gpt_main0.bin
[Read Ok] : NON-HLOS.bin
[Read Ok] : sbl1.mbn
[Read Ok] : sec.dat
[Read Ok] : emmc_appsboot.mbn
[Read Ok] : rpm.mbn
[Read Ok] : tz.mbn
[Read Ok] : hyp.mbn
[Read Ok] : fs_gc.img
[Read Ok] : misc.img
[Read Ok] : persist.img
[Read Ok] : asuskey.bin
[Read Ok] : asuskey2.bin
[Read Ok] : asuskey3.bin
[Read Ok] : asuskey4.bin
[Read Ok] : asuskey5.bin
[Read Ok] : asusfw.bin
[Read Ok] : asdf.bin
[Read Ok] : apd.bin
[Read Ok] : adf.bin
[Read Ok] : cache.img
[Read Ok] : boot.img
[Read Ok] : recovery.img
[Read Ok] : system.img
[Read Ok] : userdata.img
[Read Ok] : gpt_backup0.bin

Android Info saved!
Read finished!
Configuration : MSM8916 / eMMC
Firmware Size : 2112 MiB

Done!

syarat-dan-ketentuan

Fix Asus X009DA Dead via 9008 ~ CM2

Device Brand    : asus
Device Manufact.: asus
Device Model    : msm8916_32
Device CPU      : MSM8916
Device IntName  : WW_Phone
Device Version  : 6.0.1
CU_SWVer        : asus_x009da
Device Compile  : 3/29/2017 10:02:02 AM

Fix Asus X009DA matot via 9008, tool wajib pake CM2.

Bahan :

  • via EDL 9008 / CM2
  1.       Download Rom Asus X009DA HS-9008  atau Download Disini
  2.       Tool WAJIB menggunakan dongle CM2 
  3.       Cara kerja ikuti petunjuk CM2, boot volume up+down, kabel edl
  4.       Konfirmasi pass sms only 0822-1163-1565 (nomor ini hanya buat konfirmasi, BUKAN     YANG DI ISI) , Mahar pulsa 10k

Cara Flash Asus X009DA via dongle CM2


Operation : Read Flash [ v1.16 ]

1. Power Off Phone , Remove battery , Insert back
2. PRESS and HOLD BOTH VOLUME KEYS!
3. Insert USB cable. In some cases require use EDL cable or TP to force EDL mode!

Wait for phone…
Device Found!
Initialize …
Handshake passed!
ID_BLOCK_I : SnapDragon 410 [MSM8916]
ID_BLOCK_S : 09F6ED7C
ID_BLOCK_L : 4B05FC6FC932A2372DC731FBDB7B5FDD
ID_BLOCK_L : 238EEACE428CCE9EE75A26A3FF8B1F7B
Use CM2 Internal Loader
Loader Sent! Initializing …
Running FireHose on BBID : MSM8916 , FLASH : eMMC , mVER : 1
MemInfo : 0x0003 / 0x0200 / 0x00000001D2000000 [ eMMC 8 GiB ]
ExtInfo : 0x00004000/00004000/00001000/00001000/00000200
Boot Ok!

Brand     : asus
ProdName  : WW_Phone
Device    : msm8916_32
AndroidVer: 6.0.1
Manufact. : asus
QLMxCPU   : MSM8916
Asus X009DA
DevInfo : MSM8916__asus__asus__ANDR_v6.0.1__msm8916_32__WW_Phone

Reading Flash Content …
[Read Ok] : gpt_main0.bin
[Read Ok] : NON-HLOS.bin
[Read Ok] : sbl1.mbn
[Read Ok] : sec.dat
[Read Ok] : emmc_appsboot.mbn
[Read Ok] : rpm.mbn
[Read Ok] : tz.mbn
[Read Ok] : hyp.mbn
[Read Ok] : fs_gc.img
[Read Ok] : misc.img
[Read Ok] : persist.img
[Read Ok] : asuskey.bin
[Read Ok] : asuskey2.bin
[Read Ok] : asuskey3.bin
[Read Ok] : asuskey4.bin
[Read Ok] : asuskey5.bin
[Read Ok] : asusfw.bin
[Read Ok] : asdf.bin
[Read Ok] : apd.bin
[Read Ok] : adf.bin
[Read Ok] : cache.img
[Read Ok] : boot.img
[Read Ok] : recovery.img
[Read Ok] : system.img
[Read Ok] : userdata.img
[Read Ok] : gpt_backup0.bin

Android Info saved!
Read finished!
Configuration : MSM8916 / eMMC
Firmware Size : 2112 MiB

Done!

Flash Coolpad E560 via Fastboot & HS-9008 (MATOT)

COOLPAD E560
Brand     : Coolpad
ProdName  : cpkmini_g00
ProdModel : Coolpad E560
Device    : cpkmini_g00
AndroidVer: 5.1.1
Manufact. : Coolpad
QLMxCPU   : MSM8916

Bahan :

  • via Fastboot :
  1.      Download Fastboot Rom Coolpad E560  atau Download Disini
  2.      Download Tool dan Driver Coolpad E560 atau Download Disini (PASS YGDP : 369)
  3.      Untuk tutorial flash  bisa dilihat video dibawah
  • via EDL 9008 / CM2
  1.       Download Rom Coolpad E560 HS-9008  atau Download Disini
  2.       Tool WAJIB menggunakan dongle CM2 
  3.       Cara kerja ikuti petunjuk CM2, boot volume up+down, kabel edl

Konfirmasi pass sms only 0822-1163-1565 (nomor ini hanya buat konfirmasi, BUKAN YANG DI ISI) , Mahar pulsa 10k

 Cara Kerja :

1.    Matikan Coolpad E560 anda
2.    Tekan Volume up terus colok kabel USB, sehingga tampil seperti gambar dibawah

3.    Tekan Tobol Volume Up lagi, dan muncul tulisan seperti gambar dibawah

4.    Install driver dan Tool Coolpad E560 yang ada diatas
5.    Buka YGDP dengan Password 369
6.    Selanjutnya anda bisa lihat video dibawah

Video cara flash Coolpad E560

Log Read Firmware Coolpad E560
Operation : Read Flash [ v1.15 ]

1. Power Off Phone , Remove battery , Insert back
2. PRESS and HOLD BOTH VOLUME KEYS!
3. Insert USB cable. In some cases require use EDL cable or TP to force EDL mode!

Wait for phone…
Device Found!
Initialize …
Handshake passed!
BB_IDC_CPU : SnapDragon 410 [MSM8916]
ID_BLOCK_S : 0E813F4C
ID_BLOCK_I : 007050E1
ID_BLOCK_E : 00480000
ID_BLOCK_L : 98598B2F8FB813FB7CAE5AAE6B163EC4
ID_BLOCK_L : FA3D8AA8BB21D8D8AA2C7512E1C79892
Use CM2 Internal Loader
Loader Sent! Initializing …
Running FireHose on BBID : MSM8916 , FLASH : eMMC , mVER : 1
MemInfo : 0x0003 / 0x0200 / 0x00000001D2000000 [ eMMC 8 GiB ]
ExtInfo : 0x00004000/00004000/00001000/00001000/00000200
Boot Ok!

Brand     : Coolpad
ProdName  : cpkmini_g00
ProdModel : Coolpad E560
Device    : cpkmini_g00
AndroidVer: 5.1.1
Manufact. : Coolpad
QLMxCPU   : MSM8916

DevInfo : MSM8916__Coolpad__Coolpad__ANDR_v5.1.1__Coolpad_E560__cpkmini_g00__cpkmini_g00

Reading Flash Content …
[Read Ok] : gpt_main0.bin
[Read Ok] : sbl1.mbn
[Read Ok] : rpm.mbn
[Read Ok] : tz.mbn
[Read Ok] : hyp.mbn
[Read Ok] : param.cfg
[Read Ok] : cache.img
[Read Ok] : persist.img
[Read Ok] : misc.img
[Read Ok] : oem.img
[Read Ok] : fs_gc.img
[Read Ok] : sec.dat
[Read Ok] : emmc_appsboot.mbn
[Read Ok] : boot.img
[Read Ok] : recovery.img
[Read Ok] : system.img
[Read Ok] : NON-HLOS.bin
[Read Ok] : userdata.img
[Read Ok] : gpt_backup0.bin
Android Info saved!
Read finished!
Configuration : MSM8916 / eMMC
Firmware Size : 1349 MiB
Done!

Flash Advan S4T SC7731 & SC7731C

Model Name  : S4T
Model Brand : ADVAN
Model Device: S4T
AndrVersion : 5.1.2
BaseBand CPU: S4T
Project Ver : S4T_WG4036_V0.5_20160406
Model Ext   : S4T

Bahan :

  1.  Download Firmware PAC ADVAN S4T V0.5 atau  Download Disini
  2.  Download Firmware PAC ADVAN S4T V1.2 atau  Download Disini
  3.  Download SPD_Upgrade_Tool_R4.0.0001 Download Disini
  4.  Driver SPD by InfinityBox
  5.  Tutorial Flash via research here
  6.  Konfirmasi pass sms only 0822-1163-1565 (nomor ini hanya buat konfirmasi, BUKAN YANG DI ISI) , Mahar pulsa 10k

Error pada research download baca disini

Note :
1. Boot Volume UP
2. Buat cek versi V05 atau V1.2 flash saja, bila tidak jalan berarti versi satunya

Cara Flash Advan S4T via Research Download

Log Read Firmware Advan S4T
Operation : Read FullFlash [ v1.27 ]

1. Remove battery. Insert battery back
2. Press and hold ‘VolumeUp’ and ‘VolumeDown’ keys
 -> Alternative : just ONE ‘VolumeUp’ or ‘VolumeDown’ key
3. Insert cable
 ====  Wait for phone…
Phone found! [ 34 ]
Port Opened
Sync…
InitBoot Done [ 0x81 ] , Ver : SPRD3
Sync…
Sending FDL
[Info] : If SW freeze here more, than 15 seconds – remove cable
FDL Ready!
Boot Ver : SPRD 773x eMMC loader v3 Infinity
Sending FLASH FDL
FLASH FDL Ready!
Boot Ok!
FlashMode Set : Ok!
Detected eMMC Flash , Structure detect Ok!
[FW_READER] : Prepare Ok!
– > Wait phone connected …
Phone found! [ 34 ]
Port Opened
Sync…
InitBoot Done [ 0x81 ] , Ver : SPRD3
Sync…
Sending FDL
[Info] : If SW freeze here more, than 15 seconds – remove cable
FDL Ready!
Boot Ver : SPRD 773x eMMC loader v3 Infinity
Sending FLASH FDL
FLASH FDL Ready!
Boot Ok!

– > Wait phone connected …

Phone found! [ 34 ]
Port Opened
Sync…
InitBoot Done [ 0x81 ] , Ver : SPRD3
Sync…
Sending FDL
[Info] : If SW freeze here more, than 15 seconds – remove cable
FDL Ready!
Boot Ver : SPRD 773x eMMC loader v3 Infinity
Sending FLASH FDL
FLASH FDL Ready!
Boot Ok!

Model Name  : S4T
Model Brand : ADVAN
Model Device: S4T
AndrVersion : 5.1.2
BaseBand CPU: S4T
Project Ver : S4T_WG4036_V0.5_20160406
Model Ext   : S4T

[Read Mode] : HSUSB : 0x3000
[FW_READER] : Reading Firmware Now …
[Read Ok] : u-boot-spl-16k.bin
[Read Ok] : u-boot.bin
[Read Ok] : prodnv.img
[Read Ok] : sc7731g_CP0_modem.bin
[Read Ok] : DSP_DM_Gx.bin
[Read Ok] : nvitem_w.bin
[Read Ok] : sc8830g_modem_CP2_WCN_14D_W15.31.1_Release.bin
[Read Ok] : nvitem_wcn.bin
[Read Ok] : logo_480x800.bin
[Read Ok] : fblogo_480x800.bin
[Read Ok] : boot.img
[Read Ok] : system.img
[Build Ok] : cache.img
[Read Ok] : recovery.img
[Build Ok] : userdata.img
AndroidInfo created
Firmware Size : 1276 MiB
Saved to : F:\ADVAN\ADVAN S4T\v05 ok\S4T_S4T_5.1.2_S4T_WG4036_V0.5_20160406_S4T\
Done!

Flash Mito A260 Kitkat & Lolypop

Model Name  : MITO_A260
Model Brand : MITO
Model Device: MITO_A260
AndrVersion : 4.4.2
BaseBand CPU: H620
Project Ver : MITO_A260_20150612_T04
Model Ext   : MITO_A260

Mito A260 KitKat T04 Disticker backcasing V3
Mito A260 KitKat T07 Disticker backcasing V2

Bahan :

  1.  Download Firmware PAC Mito A260 KitKat T04 atau  Download Disini
  2.  Download Firmware PAC Mito A260 KitKat T07 atau  Download Disini
  3.  Download Firmware PAC Mito A260 Lolypop T09 atau  Download Disini
  4.  Download SPD_Upgrade_Tool_R4.0.0001 Download Disini
  5.  Driver SPD by InfinityBox
  6.  Tutorial Flash via research here
  7.  Konfirmasi pass sms only 0822-1163-1565 (nomor ini hanya buat konfirmasi, BUKAN YANG DI ISI) , Mahar pulsa 10k

Error pada research download baca disini

Note :
1. Boot Volume DOWN

Cara Flash Mito A260 via Research Download

Log Read Firmware Mito A260
Operation : Read FullFlash [ v1.27 ]

1. Remove battery. Insert battery back
2. Press and hold ‘VolumeUp’ and ‘VolumeDown’ keys
 -> Alternative : just ONE ‘VolumeUp’ or ‘VolumeDown’ key
3. Insert cable
 ====  Wait for phone…
Phone found! [ 7 ]
Port Opened
Sync…
InitBoot Done [ 0x81 ] , Ver : SPRD3
Sync…
Sending FDL
[Info] : If SW freeze here more, than 15 seconds – remove cable
FDL Ready!
Boot Ver : SPRD 773x eMMC loader v3 Infinity
Sending FLASH FDL
FLASH FDL Ready!
Boot Ok!

FlashMode Set : Ok!
Detected eMMC Flash , Structure detect Ok!

[FW_READER] : Prepare Ok!
– > Wait phone connected …

Phone found! [ 7 ]
Port Opened
Sync…
InitBoot Done [ 0x81 ] , Ver : SPRD3
Sync…
Sending FDL
[Info] : If SW freeze here more, than 15 seconds – remove cable
FDL Ready!
Boot Ver : SPRD 773x eMMC loader v3 Infinity
Sending FLASH FDL
FLASH FDL Ready!
Boot Ok!
– > Wait phone connected …

Phone found! [ 7 ]
Port Opened
Sync…
InitBoot Done [ 0x81 ] , Ver : SPRD3
Sync…
Sending FDL
[Info] : If SW freeze here more, than 15 seconds – remove cable
FDL Ready!
Boot Ver : SPRD 773x eMMC loader v3 Infinity
Sending FLASH FDL
FLASH FDL Ready!
Boot Ok!
Model Name  : MITO_A260
Model Brand : MITO
Model Device: MITO_A260
AndrVersion : 4.4.2
BaseBand CPU: H620
Project Ver : MITO_A260_20150612_T04
Model Ext   : MITO_A260
[Read Mode] : HSUSB : 0x3000

[FW_READER] : Reading Firmware Now …

[Read Ok] : u-boot-spl-16k.bin
[Read Ok] : u-boot.bin
[Read Ok] : prodnv.img
[Read Ok] : sc7731g_CP0_modem.bin
[Read Ok] : DSP_DM_Gx.bin
[Read Ok] : nvitem_w.bin
[Read Ok] : sc7731g_modem_CP2_WCN_14E_W14.50_Release.bin
[Read Ok] : nvitem_wcn.bin
[Read Ok] : logo_480x800.bin
[Read Ok] : fblogo_480x800.bin
[Read Ok] : boot.img
[Read Ok] : system.img
[Build Ok] : cache.img
[Read Ok] : recovery.img
[Build Ok] : userdata.img

AndroidInfo created
Firmware Size : 907 MiB
Saved to : E:\andro 1\mito\MITO A260\H620_MITO_A260_4.4.2_MITO_A260_20150612_T04_MITO_A260\
Done!

Flash Axioo PICOphone M4P+ (M3)

Model Name  : PICOphone_M4P_M3
Model Brand : Axioo
Model Device: PICOphone_M4P_M3
AndrVersion : 5.1
BaseBand CPU: SP7731GEA_HDR
Project Ver : PICOphone_M4P_GEP8_20151209
Model Ext   : PICOphone_M4P_M3


Bahan :

  1.  Download Firmware PAC Axioo PICOphone M4P+ (M3) atau  Download Disini
  2.  Download SPD_Upgrade_Tool_R4.0.0001 Download Disini
  3.  Driver SPD by InfinityBox
  4.  Tutorial Flash via research here
  5.  Konfirmasi pass sms only 0822-1163-1565 (nomor ini hanya buat konfirmasi, BUKAN YANG DI ISI) , Mahar pulsa 10k

Error pada research download baca disini

Note :
1. Boot Volume UP+DOWN

Cara Flash Axioo PICOphone M4P+ (M3) via Research Download

Log Read Firmware Axioo PICOphone M4P+ (M3)
Operation : Read FullFlash [ v1.27 ]

1. Remove battery. Insert battery back
2. Press and hold ‘VolumeUp’ and ‘VolumeDown’ keys
 -> Alternative : just ONE ‘VolumeUp’ or ‘VolumeDown’ key
3. Insert cable

 ====  Wait for phone…

Phone found! [ 7 ]
Port Opened
Sync…
InitBoot Done [ 0x81 ] , Ver : SPRD3
Sync…
Sending FDL
[Info] : If SW freeze here more, than 15 seconds – remove cable
PickUp loaders from pac
FDL Ready!
Boot Ver : Spreadtrum Boot Block version 1.1
Sending FLASH FDL
FLASH FDL Ready!
Boot Ok!

FlashMode Set : Ok!
Detected eMMC Flash , Structure detect Ok!

[FW_READER] : Prepare Ok!
– > Wait phone connected …

Phone found! [ 7 ]
Port Opened
Sync…
InitBoot Done [ 0x81 ] , Ver : SPRD3
Sync…
Sending FDL
[Info] : If SW freeze here more, than 15 seconds – remove cable
PickUp loaders from pac
FDL Ready!
Boot Ver : Spreadtrum Boot Block version 1.1
Sending FLASH FDL
FLASH FDL Ready!
Boot Ok!

– > Wait phone connected …

Phone found! [ 7 ]
Port Opened
Sync…
InitBoot Done [ 0x81 ] , Ver : SPRD3
Sync…
Sending FDL
[Info] : If SW freeze here more, than 15 seconds – remove cable
PickUp loaders from pac
FDL Ready!
Boot Ver : Spreadtrum Boot Block version 1.1
Sending FLASH FDL
FLASH FDL Ready!
Boot Ok!

Model Name  : PICOphone_M4P_M3
Model Brand : Axioo
Model Device: PICOphone_M4P_M3
AndrVersion : 5.1
BaseBand CPU: SP7731GEA_HDR
Project Ver : PICOphone_M4P_GEP8_20151209
Model Ext   : PICOphone_M4P_M3

[Read Mode] : HSUSB : 0x3000

[FW_READER] : Reading Firmware Now …

[Read Ok] : u-boot-spl-16k.bin
[Read Ok] : u-boot.bin
[Read Ok] : prodnv.img
[Read Ok] : sc7731g_CP0_modem.bin
[Read Ok] : DSP_DM_Gx.bin
[Read Ok] : nvitem_w.bin
[Read Ok] : sc8830g_modem_CP2_WCN_14D_W15.28.4_Release.bin
[Read Ok] : nvitem_wcn.bin
[Read Ok] : logo_720x1280.bin
[Read Ok] : fblogo_720x1280.bin
[Read Ok] : boot.img
[Read Ok] : system.img
[Build Ok] : cache.img
[Read Ok] : recovery.img
[Build Ok] : userdata.img

AndroidInfo created
Firmware Size : 1974 MiB
Saved to : D:\axioo\m4p m3\m4p+ m3\SP7731GEA_HDR_PICOphone_M4P_M3_5.1_PICOphone_M4P\
Done!

Flash Huawei CUN-L22 BI / Bahasa Indonesia

platform: MT6735, cpu abi: armeabi-v7a
manufacturer: HUAWEI
board: CUN-L22, name: CUN-L22
brand: HUAWEI, model: HUAWEI CUN-L22
build id: HUAWEICUN-L22, version: 5.1 Lollipop (CUN-L22C567B130)
build description: full_hq6735_35u_b1n_l1-user 5.1 HUAWEI 1491876625 test-keys
build version: ALPS.L1.MP3.HQ6753.65C.B1N.L1.V1_HQ6735.35U.B1N.L1_P16

Bahan :
1. Download Firmware Huawei CUN-L22  & Tool C567B130 atau Download Disini
2. Download Firmware Huawei CUN-L22 versi lain dibawah
3. Driver bila belum punya instal dulu driver mtknya
4. Untuk tutorial flash via Flash tool bisa dilihat DISINI
5. Konfirmasi pass sms only 0822-1163-1565 (nomor ini hanya buat konfirmasi, BUKAN YANG DI ISI) , Mahar pulsa 10k

Rom Huawei CUN-L22 versi lain :

Langkah kerja :
1. Download dan extrax, nama folder pendek saja, jangan pake sub folder kebanyakan
2. Buka Flash tool
3. Klik download Agent arahkan ke ROM CUN-L22 + Tool\SP_Flash_Tool_exe_Windows_v5.1548.00.000-secure\808_sec_da\ => pilih DA_SWSEC.bin
4. Pilih scatter , uncheck preloader
5. Flash
Untuk lengkapnya silahkan lihat video di bawah

Note:
untuk FRP CUN-L22 :
1. Pake UFI => Ganti DA dgn 808_sec_da\DA_SWSEC.bin yg ada difolder flashtool, isikan scatter, identify, baru reset frp

2. atau search digoogle

Cara Flash Huawei CUN-L22 via Flash Tool

Log Read Firmware Huawei Cun L22
Manufacturer ID: 0x90 (SK Hynix)
Product name: H8G1e (0x483847316505), rev: 0x07, serial number: 0x54A8A01A
Manufacturing date: Sep 2016
CID: 90014A48 38473165 050754A8 A01A93C3
Capacity: 7.29 GiB(7,830,765,568 bytes)
 Boot1: 4096 KiB
 Boot2: 4096 KiB
 RPMB: 4096 KiB
 User area: 7.28 GiB(7,818,182,656 bytes)
platform: MT6735, cpu abi: armeabi-v7a
manufacturer: HUAWEI
board: CUN-L22, name: CUN-L22
brand: HUAWEI, model: HUAWEI CUN-L22
build id: HUAWEICUN-L22, version: 5.1 Lollipop (CUN-L22C567B130)
build description: full_hq6735_35u_b1n_l1-user 5.1 HUAWEI 1491876625 test-keys
build version: ALPS.L1.MP3.HQ6753.65C.B1N.L1.V1_HQ6735.35U.B1N.L1_P16
screen resolution: 1280 x 720
main camera: ov13850_mipi_raw ov13850qt_mipi_raw ov8855_mipi_raw s5k4h8_mipi_raw imx219_mipi_raw hi843b_808_mipi_raw
 lens: dw9714ov13850af bu6424af dw9714af dw9714qtaf dw9714imx219af dw9714hi843b808af
front camera: ov5670_mipi_raw hi551_mipi_raw gc2355_mipi_raw sp2508_mipi_raw sp2509_mipi_raw
audio: amp_6323pmic_spk
touch: GT9157
Reading preloader_hq6735_35u_b1n_l1.bin… Done.
Reading pgpt… Done.
Reading proinfo.bin… Done.
Reading nvram… Done.
Reading protect1… Done.
Reading protect2… Done.
Reading lk.bin… Done.
Reading para… Done.
Reading boot.img… Done.
Reading recovery.img… Done.
Reading logo.bin… Done.
Reading expdb… Done.
Reading rootm… Done.
Reading seccfg… Done.
Reading oemkeystore… Done.
Reading secro.img… Done.
Reading keystore… Done.
Reading trustzone.bin… Done.
Reading trustzone.bin… Done.
Reading oeminfo… Done.
Reading frp… Done.
Reading nvdata… Done.
Reading metadata… Done.
Reading flashinfo… Done.
Files saved to \\E:\huawei\huawei%20cun%20l22\New%20folder\

Flash ZTE V811W via CM2 (HS-9008) & SDCARD

Brand     : ZTE
ProdName  : ZTE-V811
ProdModel : ZTE V811W
Device    : P821E10
AndroidVer: 4.4.2
Manufact. : ZTE
QLMxCPU   : MSM8610
DevInfo : MSM8610__ZTE__ZTE__ANDR_v4.4.2__ZTE_V811W__P821E10__ZTE-V811

Bahan :
1.Via HS-9008 Tool wajib Infinity CM2 atau Unitool/volcano

2. Via SD-CARD / MMC

3. Tutorial silahkan lihat di video di bawah
4. Konfirmasi pass sms only 0822-1163-1565 (nomor ini hanya buat konfirmasi, BUKAN YANG DI ISI) , Mahar pulsa 10k

Cara Flash ZTE V811W via CM2 (Boot volume up+down colok kabel EDL)

Cara Flash ZTE V811W via SDCARD
1. Sesuaikan versi
2. Copy Update.zip ke mmc, masukkan ke ZTE V811W
3. Tekan Volume up terus tekan on, tunggu sampai masuk ke recovery
4. Wipe dulu, data & cache
5. Pilih upply update from sdcard
6. Tunggu same done, reboot

Log Read Flash ZTE V811W
 Operation : Read Flash [ v1.11 ]

1. Power Off Phone , Remove battery , Insert back
2. PRESS and HOLD BOTH VOLUME KEYS!
3. Insert USB cable. In some cases require use EDL cable or TP to force EDL mode!

Wait for phone…
Device Found!
Initialize …
Handshake passed!
BB_IDC_CPU : SnapDragon 2x/4x|00 [MSM8x10]
ID_BLOCK_S : 0576C200
ID_BLOCK_I : 008110E1
ID_BLOCK_L : 857F15E14CDAC7C2BD926263ACF77F4F
ID_BLOCK_L : 2D20EE4132DD0D863BFADF141E918FCC
Use CM2 Internal Loader
Loader Sent! Initializing …
Running FireHose on BBID : MSM8x10 , FLASH : eMMC , mVER : 1
ExtInfo : 0x0000C000/0000C000/00001000/00001000
Boot Ok!
Brand     : ZTE
ProdName  : ZTE-V811
ProdModel : ZTE V811W
Device    : P821E10
AndroidVer: 4.4.2
Manufact. : ZTE
QLMxCPU   : MSM8610
DevInfo : MSM8610__ZTE__ZTE__ANDR_v4.4.2__ZTE_V811W__P821E10__ZTE-V811
Reading Flash Content …
[Read Ok] : gpt_main0.bin
[Read Ok] : NON-HLOS.bin
[Read Ok] : sbl1.mbn
[Read Ok] : deploy.mbn
[Read Ok] : emmc_appsboot.mbn
[Read Ok] : rpm.mbn
[Read Ok] : boot.img
[Read Ok] : tz.mbn
[Read Ok] : system.img
[Read Ok] : userdata.img
[Read Ok] : persist.img
[Read Ok] : cache.img
[Read Ok] : recovery.img
[Read Ok] : misc.img
[Read Ok] : fs_gc.img
[Read Ok] : splash.img
[Read Ok] : gpt_backup0.bin

Android Info saved!
Read finished!
Configuration : MSM8x10 / eMMC
Firmware Size : 785 MiB

Done!

Flash Mito A91 SP7731CEA T08

Model Name  : A91
Model Brand : MITO
Model Device: A91
AndrVersion : 6.0
BaseBand CPU: SP7731CEA
Project Ver : MITO_A91_20161223_648_B1T08
Model Ext   : MITO A91

Bahan :

  1.  Download Firmware PAC MITO A91 T08 atau Download Disini
  2.  Download Firmware PAC MITO_A91_T12 atau Download Disini
  3.  Download SPD_Upgrade_Tool_R4.0.0001 Download Disini
  4.  Driver SPD by InfinityBox
  5.  Tutorial Flash via research here
  6.  Konfirmasi pass sms only 0822-1163-1565 (nomor ini hanya buat konfirmasi, BUKAN YANG DI ISI) , Mahar pulsa 10k

Error pada research download baca disini

Note :
1. Boot Volume +/-
2. Tested buat versi T08

Cara Flash Mito A91 via SPD UPGRADE TOOL

 Log Read Firmware Mito A91
Operation : Read FullFlash [ v1.27 ]

1. Remove battery. Insert battery back
2. Press and hold ‘VolumeUp’ and ‘VolumeDown’ keys
 -> Alternative : just ONE ‘VolumeUp’ or ‘VolumeDown’ key
3. Insert cable

 ====  Wait for phone…

Phone found! [ 34 ]
Port Opened
Sync…
InitBoot Done [ 0x81 ] , Ver : SPRD3
Sync…
Sending FDL
[Info] : If SW freeze here more, than 15 seconds – remove cable
FDL Ready!
Boot Ver : SC7731 Crev eMMC Loader v2.0    
Sending FLASH FDL
FLASH FDL Ready!
Boot Ok!
FlashMode Set : Ok!
Detected eMMC Flash , Structure detect Ok!
[FW_READER] : Prepare Ok!
– > Wait phone connected …
Phone found! [ 34 ]
Port Opened
Sync…
InitBoot Done [ 0x81 ] , Ver : SPRD3
Sync…
Sending FDL
[Info] : If SW freeze here more, than 15 seconds – remove cable
FDL Ready!
Boot Ver : SC7731 Crev eMMC Loader v2.0    
Sending FLASH FDL
FLASH FDL Ready!
Boot Ok!

– > Wait phone connected …

Phone found! [ 34 ]
Port Opened
Sync…
InitBoot Done [ 0x81 ] , Ver : SPRD3
Sync…
Sending FDL
[Info] : If SW freeze here more, than 15 seconds – remove cable
FDL Ready!
Boot Ver : SC7731 Crev eMMC Loader v2.0    
Sending FLASH FDL
FLASH FDL Ready!
Boot Ok!
Model Name  : A91
Model Brand : MITO
Model Device: A91
AndrVersion : 6.0
BaseBand CPU: SP7731CEA
Project Ver : MITO_A91_20161223_648_B1T08
Model Ext   : MITO A91
[Read Mode] : HSUSB : 0x3000
[FW_READER] : Reading Firmware Now …
[Read Ok] : u-boot-spl-16k.bin
[Read Ok] : u-boot.bin
[Read Ok] : prodnv.img
[Read Ok] : sc7731C_CP0_modem.bin
[Read Ok] : DSP_DM_Gx.bin
[Read Ok] : nvitem_w.bin
[Read Ok] : sc8830g_modem_CP2_WCN_Trunk_W16.28.5_Release.bin
[Read Ok] : nvitem_wcn.bin
[Read Ok] : logo_480x854.bin
[Read Ok] : fblogo_480x854.bin
[Read Ok] : boot.img
[Read Ok] : system.img
[Read Ok] : sysinfo.img
[Build Ok] : cache.img
[Read Ok] : recovery.img
[Build Ok] : userdata.img

AndroidInfo created
Firmware Size : 1939 MiB
Saved to : E:\andro 1\mito\a91\t08\SP7731CEA_A91_6.0_MITO_A91_20161223_648_B1T08_MITO_A91\
Done!